Other products

SATI stands for Stand Alone Trimming Interface. It enables zeroing and trimming of the encoder after it has already been installed. Successful trimming process done with SATI improves the system’s absolute position error down to ±0.2°. It can be used for encoders made with RLS AM4096 sensor ICs only. Read more about SATI interface

For use with absolute encoders with SPI or PWM communication interface EncoSight software available under Download Electronic data sheet, encoder status, position, configuration and calibration are easy accessible via EncoSight application The E201-9P interrogates a SPI or PWM encoder and allows the data to be read by a PC using simple ASCII commands over the USB connection. Also supports complete functionality of the EncoLink protocol over SPI interface. For use with: AksIM-2 & AksIM-4 LA11 Orbis Software notice: USB drivers For Windows 10 or newer use Windows Update to install “inbox drivers”. More information is on this link. For Windows 8 or older, drivers will be installed together with the software. USB drivers will be installed together with the E201-9P software. For manual USB drivers setup please download the setup file.

The E201-9Q counts edges from 5 V incremental encoders and allows the count value to be read by a PC using simple ASCII commands over the USB connection. For use with: Artos (Only with PCB-A for DI and SI option) LM10/13/15 RE22/36 RLB RLM RM22/36 RM44/58 SpinCo HiLin FlexIN Software notice: USB drivers For Windows 10 or newer use Windows Update to install “inbox drivers”. More information is on this link. For Windows 8 or older, drivers will be installed together with the software. For manual USB drivers setup please download the setup file.

The E201-9S interrogates an SSI or BiSS encoder and allows the data to be read by a PC using simple ASCII commands over the USB connection. E201-9S supports unidirectional communication for absolute SSI and BiSS C encoders (without register access). For use with: AksIM-2 & AksIM-4 Artos LA11 LinACE Orbis RE22/36 RM22/36 RM44/58 Software notice: USB drivers For Windows 10 or newer use Windows Update to install “inbox drivers”. More information is on this link. For Windows 8 or older, drivers will be installed together with the software. For manual USB drivers setup please download the setup file.

The E201-9B interrogates a BiSS C encoder and allows data to be read by a PC with simple ASCII commands via a USB connection and a virtual COM port. E201-9B supports BiSS C bidirectional encoders. For use with: AksIM-2 & AksIM-4 Orbis Artos DHR, DHL, DBR, DBL, DHF, DBF Software notice: For manual USB drivers setup please download the setup file.

Line driver board for incremental output. Connector type: JST_SM08B-SURS-TF, 0.8mm pitch

Line driver board for SSI output. Connector type: JST SM06B-SURS-TF

AM4096 on a PCB with all necessary components and a magnet, delivered in an antistatic box. RMK4 has all outputs available, by default it is configured for 5 V supply voltage and with 12 bit resolution. RMK4 is evaluation board, not suitable for mass production. RMK4KIT is a custom made demo kit consisting of RMH06 magnetic actuator and RMK4 PCB on acrylic base with prefabricated hole to allow the magnet to be positioned inside tolerance according to the AM4096 datasheet.

The UPRG01 is a programming interface for use with compatible encoders from RLS. The encoders which support this functionality are the LM10 linear encoder, LM15 linear encoder, LM13 linear encoder and LM13 ring encoder. Note that a special option of the encoders must be ordered with this programmability enabled. The software allows the resolution, edge separation and count direction to be changed for both linear and ring encoders. The interface connects simply to a computer via a USB port.

The UPRGAM4096 is a programming interface for use with AM4096 rotary magnetic encoder chip and RMK4 evaluation board. The interface allows the user via a PC to communicate and program the internal memory of the AM4096 via the I2C protocol. A simple software interface is provided to allow easy adjustment of the available parameters as well as providing a graphical display of the position information and status of the encoder chip. The interface connects simply to a computer via a USB port.

A set of one fastener and one washer for mounting Track system elements. The number of required sets varies based on mounting method.  For additional information see datasheet LM10D18, which can be found in the Downloads.

Joining element enables joining the ends of two magnetic scales easily and thereby reaching system lengths longer than 100 m.  For additional information see datasheet LM10D18, which can be found in the Downloads.

Aluminium guide rail, 1 meter long for easy magnetic scale fitting/refitting which allows the scale to expand and contract freely.  For additional information see datasheet LM10D18, which can be found in the Downloads. Read more about TRS system NOTE – ordered scale must be TRS track system compatible

2 m long track section system for MS19/DS19.

1 m long track section system for MS19/DS19.

Double screw fix for DS19/MS19.

Aluminium guide rail, 2 meters long for easy magnetic scale fitting/refitting which allows the scale to expand and contract freely.  For additional information see datasheet LM10D18, which can be found in the Downloads. Read more about TRS system NOTE – ordered scale must be TRS track system compatible

The mounting bracket made of aluminium can be used for easy mounting and fixing of the RoLin™ readhead. Part number: RLMMB01

Zeroing pen for RM44 rotary magnetic encoder.

Cable assembly for connection of MOLEX 501330-1100, 12 core. It exists in 3 options (depending on lengths: 30, 50, 100 cm).

A special installation tool can be supplied for easier, more reliable and time-saving installation of the readhead in relation to the ring. The installation tool limits the readhead in 6 directions (ride height/radial offset, centerline/tangential, yaw, axial/lateral, pitch and roll offset) and thus ensures precise alignment of the readhead, guaranteeing optimal performance. A dedicated mounting tool is required for each SAR ring to adjust the diameter of the ring. Please check the part number diagram to select the correct installation tool for the selected ring.

Fasteners for DS19 absolute magnetic scale.

An extension cable for the DHR and DHL Artos™ readhead. The encoder side of the extension cable is equipped with the M12 connector. The termination on the controller side is selectable (flying leads, M12 or D-SUB 9 pin connector).

Molex Premo-Flex™ FFC Jumper, 6 Circuits, 152 mm, 1 mm pitch. This cable can be used with AksIM-1 MBA encoder.

For use with AksIM™ MBA-type encoders with BiSS or SSI communication interfaces to allow connection to RS422 compatible controllers or encoder interfaces. Integrated voltage protection limits voltage spikes to maximum 5.6 V. Differential lines are terminated with RC circuits for lower current consumption. Available with or without housing. 

Cable assembly with 11 pin Molex connector (PN: 501330-1100), 8 core 1 m long. Suitable to connect Orbis encoders. For details and pinout see Orbis datasheet.

Mounting bracket for RM08 super small non-contact rotary encoder. This mounting bracket can be used with RM08 encoder.

Cable assembly FCI 8 pin, flying leads, 8 wire, single shield, 1 m. Suitable to connect AksIM-2 encoder. For details and pinout see AksIM-2 datasheet.

Cable assembly FCI 8 pin, D-sub 9 pin, single shield, 1m. Suitable to connect AksIM-2 encoder to E201 interface. For details and pinout see AksIM-2 datasheet.

Cable assembly Molex 12 pin, flying leads, 12 wire, twisted pairs, shielded, 1 m. Suitable to connect AksIM-2 Redundant variant MB039xxxxxxRRT00. For details and pinout see AksIM-2 Redundant datasheet. Cable assembly Molex 12 pin, flying leads, 12 wire, twisted pairs, shielded, 1 m. Suitable to connect AksIM-2 Redundant variant MB039xxxxxxRRT00 and the Artos system. For details and pinout, see the respective datasheets for AksIM-2 Redundant and Artos systems.

Cable assembly Molex 11 pin, flying leads, 8 wire, single shield, 3 m. Suitable to connect AksIM-2 and Orbis encoders. For details and pinout see Orbis datasheet.

Cable assembly Molex 11 pin, D-sub 9 pin, single shield, 1 m. Suitable to connect Orbis encoders to E201 interface. For details and pinout see Orbis datasheet.

Cable assembly Molex 15133-0603 for connection with Molex 501568-0607. This cable can be used with RMB20Sx_96 encoder.

Cable Assembly Molex 11 pin, flying lead, 1 m.

Cable Assembly Molex 11 pin, DB9, 1 m. For connection to E201.

Molex Premo-Flex™ FFC Jumper, 6 Circuits, 203 mm, 0.5 mm pitch. This cable can be used with RMB14SC encoder.

Molex Premo-Flex™ FFC Jumper, 8 Circuits, 203 mm, 0.5 mm pitch. This cable can be used with RMB14IC encoder.

FFC Cable, 20 Core, 0.5 mm pitch, Same Sided Contacts, 152 mm (6 inch) length. This encoder can be used with AksIM-2 redundant encoder.

Cable assembly with dual ended JST connectors - SSI output. For use with LDB02 and RMB14 SSI output , please choose 6 pin.

Cable assembly with dual ended JST connectors - SSI output. For use with LDB02 and RMB14 SSI output , please choose 6 pin.

Cable assembly with dual ended JST connectors - incremental output. For use with LDB01, please chose pin 8.

Cable assembly with dual ended JST connectors - incremental output. For use with LDB01, please chose pin 8.

Breakout board FFC 20 pin, 0.5 mm TO 2X FCI8 Pin and soldering holes. This breakout board can be used with AksIM-2 redundant encoder.

Applicator Tool for Magnetic Scale with HiLin.

Cable Assembly Molex 11 pin to Flying Leads, 1 m, OD 6.2 mm, max.temp 80 °C. Suitable to connect Orbis encoders. For details and pinout see Orbis datasheet.

Cable assembly FCI 8 pin, flying leads, 8 wire, single shield, 1 m, OD 6.2 mm, max.temp 80 °C. Suitable to connect AksIM-2 encoder. For details and pinout see AksIM-2 datasheet.

ACC050 - 76.2 mm long

ACC051 - 152.4 mm long

ACC052 - 304.8 mm long

ACC053 - 609.6 mm long

Cable assembly ACC054, Molex connector, flying leads, length 1 m. Suitable to connect RLC2IC encoder with connector option 12 - Molex 5015681107.

Cable assembly ACC055, Molex connector, DB-9 connector, length 1 m. Suitable to connect RLC2IC encoder with connector option 12 - Molex 5015681107.

Cable assembly ACC056, Amphenol connector, flying leads, length 1 m. Suitable to connect RLC2IC encoder with connector option 20 - Connector AMPHENOL 10114828-11108LF.

Cable assembly ACC057, Amphenol connector, DB-9 connector, length 1 m. Suitable to connect RLC2IC encoder with connector option 20 - Connector AMPHENOL 10114828-11108LF.

Cable assembly ACC058, FFC connector, length 152 mm. Suitable to connect RLC2IC encoder with connector option 13 - Connector Molex 527451197.

Cable assembly ACC059, FFC connector, length 305 mm.

Cable assembly FCI 8 pin, flying leads, 8 wire, single shield, 3 m. Suitable to connect AksIM-2 encoder. For details and pinout see AksIM-2 datasheet.

Cable assembly FCI 8 pin, D-sub 9 pin, single shield, 1 m, OD 6.2 mm, max. temp 80 °C. Suitable to connect AksIM-2 encoder to E201 interface. For details and pinout see AksIM-2 datasheet.

Cable Assembly Molex 11 pin to Flying Leads, 3 m, OD 6.2 mm, max. temp 80 °C. Suitable to connect Orbis encoders. For details and pinout see Orbis datasheet.

Cable assembly Molex 11 pin, D-sub 9 pin, single shield, 1 m. OD 6.2 mm, max. temperature 80 °C. Suitable to connect Orbis encoders to E201 interface. For details and pinout see Orbis datasheet.

Cable assembly Molex 11 pin, BB, Flying leads, single shield, 1 m. OD 6.2 mm, max. temperature 80 °C. Suitable to connect Orbis Battery Backup Multiturn encoder. For details and pinout see Orbis Battery Backup Multiturn datasheet.

Cable assembly Molex 11 pin, BB, D-sub 9 pin, single shield, 1 m. OD 6.2 mm, max. temperature 80 °C. Suitable to connect Orbis Battery Backup Multiturn encoder. For details and pinout see Orbis Battery Backup Multiturn datasheet.

Cable assembly FCI 8 pin, flying leads, 8 wire, single shield, 3 m, OD 6.2 mm, max. temperature 80 °C. Suitable to connect AksIM-2 encoder. For details and pinout see AksIM-2 datasheet.

Installation Accessory set for RM16 & RE16.

CAACC001 - Installation accessory set for LinACE with 8 mm shaft diameter

CAACC003 - Installation accessory set for LinACE with 12 mm shaft diameter

CAACC004 - Installation accessory set for LinACE with 6 mm shaft diameter.

MHA7TACC01 Alignment tool for MHA7 readhead / MRA7 ring radial positioning MHA8TACC01 Alignment tool for MHA8 readhead / MRA8 ring radial positioning

Cable assembly, 4 pin, 0.5 m, dual ended JST connectors. Compatible with RMB14Vx with header connector.

Cable assembly, 4 pin, 1 m, dual ended JST connectors. Compatible with RMB14Vx with header connector.

The magnetic field viewer MM001 offers the easiest and fastest way to view the magnetised pattern of magnetic scales or rings. Above the magnetic field viewer foil there is a ruler with which the magnetic poles per cm of a magnet can be measured.

RLACC connector adapter is a tool for connecting any readhead from RoLin product family to an E201 communication interface or similar subsequent electronics. It enables easy connection between RoLin’s 10 or 6 pin flex cable and 9 pin D type connector.

Aluminium flat bracket for the Artos DBR and DBL readhead.

This applicator tool helps you to position the stick-on reference mark at the required position. Part number: LM10ARM00

Aluminium angled bracket for the Artos DBR and DBL readhead.

The stick-on reference mark can be easily applied to the magnetic scale. Part number: LM10SRM00

Rolling tool for FlexAB DHF.

Rolling tool for FlexAB DBR with ACC080.

Rolling tool for FlexAB DBR.

This applicator tool can be mounted in place of any RLS LM10 readhead and uses motion of the axis to apply the MS magnetic scale parallel to the guideway. Part number: LM10ASC00

 The end clamps have been designed to anchor the ends of the MS magnetic scale. Part number: LM10ECL00

This applicator tool can be mounted in place of any RLS LM13 readhead and uses motion of the axis to apply the MS tape scale parallel to the guideway. Part number: LM13ASC00

Applicator tool LMA10ASC00 for magnetic scale and cover foil. Part number: LMA10ASC00

Aluminium scale clamp securely retains the magnetic scale and provides a fixed point from which the MS scale can expand.  For additional information see MS Incremental Magnetic scales data sheet, which can be found in the Downloads section.

Washer for SAS and HMS scales.

Shims for adjusting ride height during AksIM-2 mounting. *Shims are available in multiples of 5.

Shims for adjusting ride height during AksIM-4 mounting. *Shims are available in multiples of 5.