Accessories

Line driver board for incremental output. Connector type: JST_SM08B-SURS-TF, 0.8mm pitch

Line driver board for SSI output. Connector type: JST SM06B-SURS-TF

A set of one fastener and one washer for mounting Track system elements. The number of required sets varies based on mounting method.  For additional information see datasheet LM10D18, which can be found in the Downloads.

Joining element enables joining the ends of two magnetic scales easily and thereby reaching system lengths longer than 100 m.  For additional information see datasheet LM10D18, which can be found in the Downloads.

Aluminium guide rail, 1 meter long for easy magnetic scale fitting/refitting which allows the scale to expand and contract freely.  For additional information see datasheet LM10D18, which can be found in the Downloads. Read more about TRS system NOTE – ordered scale must be TRS track system compatible

2 m long track section system for MS19/DS19.

1 m long track section system for MS19/DS19.

Double screw fix for DS19/MS19.

Aluminium guide rail, 2 meters long for easy magnetic scale fitting/refitting which allows the scale to expand and contract freely.  For additional information see datasheet LM10D18, which can be found in the Downloads. Read more about TRS system NOTE – ordered scale must be TRS track system compatible

The mounting bracket made of aluminium can be used for easy mounting and fixing of the RoLin™ readhead. Part number: RLMMB01

Zeroing pen for RM44 rotary magnetic encoder.

A special installation tool can be supplied for easier, more reliable and time-saving installation of the readhead in relation to the ring. The installation tool limits the readhead in 6 directions (ride height/radial offset, centerline/tangential, yaw, axial/lateral, pitch and roll offset) and thus ensures precise alignment of the readhead, guaranteeing optimal performance. A dedicated mounting tool is required for each SAR ring to adjust the diameter of the ring. Please check the part number diagram to select the correct installation tool for the selected ring.

Fasteners for DS19 absolute magnetic scale.

Mounting bracket for RM08 super small non-contact rotary encoder. This mounting bracket can be used with RM08 encoder.

Breakout board FFC 20 pin, 0.5 mm TO 2X FCI8 Pin and soldering holes. This breakout board can be used with AksIM-2 redundant encoder.

Applicator Tool for Magnetic Scale with HiLin.

CAACC001 - Installation accessory set for LinACE with 8 mm shaft diameter

CAACC003 - Installation accessory set for LinACE with 12 mm shaft diameter

CAACC004 - Installation accessory set for LinACE with 6 mm shaft diameter.

MHA7TACC01 Alignment tool for MHA7 readhead / MRA7 ring radial positioning MHA8TACC01 Alignment tool for MHA8 readhead / MRA8 ring radial positioning

The magnetic field viewer MM001 offers the easiest and fastest way to view the magnetised pattern of magnetic scales or rings. Above the magnetic field viewer foil there is a ruler with which the magnetic poles per cm of a magnet can be measured.

Aluminium flat bracket for the Artos DBR and DBL readhead.

This applicator tool helps you to position the stick-on reference mark at the required position. Part number: LM10ARM00

Aluminium angled bracket for the Artos DBR and DBL readhead.

The stick-on reference mark can be easily applied to the magnetic scale. Part number: LM10SRM00

Rolling tool for FlexAB DHF.

Rolling tool for FlexAB DBR with ACC080.

Rolling tool for FlexAB DBR.

This applicator tool can be mounted in place of any RLS LM10 readhead and uses motion of the axis to apply the MS magnetic scale parallel to the guideway. Part number: LM10ASC00

 The end clamps have been designed to anchor the ends of the MS magnetic scale. Part number: LM10ECL00

This applicator tool can be mounted in place of any RLS LM13 readhead and uses motion of the axis to apply the MS tape scale parallel to the guideway. Part number: LM13ASC00

Applicator tool LMA10ASC00 for magnetic scale and cover foil. Part number: LMA10ASC00

Aluminium scale clamp securely retains the magnetic scale and provides a fixed point from which the MS scale can expand.  For additional information see MS Incremental Magnetic scales data sheet, which can be found in the Downloads section.

Washer for SAS and HMS scales.

Shims for adjusting ride height during AksIM-2 mounting. *Shims are available in multiples of 5.

Shims for adjusting ride height during AksIM-4 mounting. *Shims are available in multiples of 5.